Search results

  1. C

    Chipper knive bolts

    Did you see the Accusharp Knife sharpener they have in the Chipper Parts section? I can only assume its possible for us to sharpen our own knives with a regular looking kitchen knife sharpener?! Northeastern seems pretty good if you have a Bandit, Im looking for Morbark Bolts
  2. Groundie with the Save: Crispy Dead Spruce Removal

    Groundie with the Save: Crispy Dead Spruce Removal

    Removal of a crispy dead Spruce in the middle of a garden, right next to the garage. I got disoriented while cutting the notch and it was up to my Rope Tech. to pull it to the lay.
    • CTtreeNWC
    • Media item
    • Comments: 0
    • Category: Tree Removal and Rigging
  3. C

    Harken riggong winch 500

    thats the same way you lower off of the GRCS. idk if maple leaf knows what hes talking about because to use the bollard on the GRCS, you need to uninstall the winch. You only use the bollard when you dont need any lift, you just lower off the winches bollard just as the directions say for both...
  4. Testing Homemade GRCS

    Testing Homemade GRCS

    Warning: All new techniques should be practiced in a controlled environment. Low and Slow. The CT Climber couldn't pass up the opportunity to try out his new homemade rigging device by removing a large limb over a house. What could go wrong?
    • CTtreeNWC
    • Media item
    • Comments: 1
    • Category: Tree Removal and Rigging
  5. C

    Comment by 'CTtreeNWC' in media 'Easy $600 Day'

    East Chatham, my girlfriend got a job in Pittsfield, Mass. So I left my very prosperous Litchfield County CT. This place isn't all that bad though. I haven't worked more than 6 miles from home yet.
  6. Easy $600 Day

    Easy $600 Day

    After moving to Upstate NY the CT Climber has ran into his fair share of cheep skates. An Easy $600 Day would hopefully turn his luck. But problems persist a...
    • CTtreeNWC
    • Media item
    • Comments: 2
    • Category: Tree Removal and Rigging
  7. C

    New Tribe Onyx Saddle discussion in light of the newest saddle releases

    truly amazing how august was able to go in there with a smile on his face and capture all of this priceless manufacturing knowledge. I wonder how many times he referenced this video while building his factory, hell he probably has some of the same workers in there.
  8. C

    Estimate sheets

    What do you think are the limitations of Wave? It looks pretty decent, Im about to give it a try. Just wondering before I start uploading all my customers information. It also makes me pause, what are they getting out of this and is my customers information safe?
  9. C

    Cordless Drill for GRCS (?)

    What brand have you had best success with? It's time I step up and buy a 9/16, considering I'm starting to grcs. I've been using old climb line the last few years but the 11.7 doesn't last as long as 1/2 would
  10. C

    What’s Your SMALLER Equipment Setup?

    Holy lord $7300 for a little chipper sans hydrolics!! The times we living in
  11. C

    What’s Your SMALLER Equipment Setup?

    Norway spruce*** not maple I must be missing my old favorite street tree.
  12. C

    New Tribe Onyx Saddle discussion in light of the newest saddle releases

    Does it have the bones where the bridge attaches? Did you tie the second bridge on the lower dees? Can't really see the picture clear, I still climb on a treemotion 2018 and often think about a second bridge.
  13. C

    Cordless Drill for GRCS (?)

    I've got the model from the original grcs, Harken 44 two speed self-tailing
  14. C

    What’s Your SMALLER Equipment Setup?

    https://gopro.com/v/dMgqnlkR2k1Wo Here's my Salsco chipper that I've almost exclusively been using while my redneck uncle has been clearing land with my Morbark. I didn't edit together a nice little clip so you can really see what the chipping experience is. This particular job was 2 Norway...
  15. C

    Cordless Drill for GRCS (?)

    What's the smallest rope you guys have used in the Harken? I only have 11.7 climb line on hand to test and it doesnt seem to self-tail very well with it. It obviously looks a bit small tho.
  16. C

    Cordless Drill for GRCS (?)

    https://photos.app.goo.gl/46LiU7NnXRRdJWWB9 Excuse the splattered brown spray paint on my harken. There was an incident involving me trying to use the spray can as a hammer in my new apartment. I had to paint some walls before my girl got home
  17. C

    Cordless Drill for GRCS (?)

    https://www.amazon.com/Powered-Furling-Wrench-Adapter-Cordless/dp/B0B62X6P9F/?_encoding=UTF8&pf_rd_p=7e3efa2e-dfa7-4eb2-af5b-d0848656d30a&pd_rd_wg=Qpvt6&pf_rd_r=YZZ5SN6A7N9PKXNEQGDZ&content-id=amzn1.sym.7e3efa2e-dfa7-4eb2-af5b-d0848656d30a&pd_rd_w=algTT&painterId=gwm-asin-tile&pd_rd_r=3cfe357e-b9...
  18. C

    Cordless Drill for GRCS (?)

    Recently received a Harken 44 for an unbelievable price. After a lot of searching I came up on this adapter also on Amazon, $15 and also can accommodate 2 different wrench sizes, that may come in handy. I'm thinking maybe a socket/ratchet may go on one as a nice handle.
  19. C

    New Tribe Onyx Saddle discussion in light of the newest saddle releases

    I'm aware of that, I was just busting homies balls because he was comparing the mb vs mb 2.0
  20. C

    New Tribe Onyx Saddle discussion in light of the newest saddle releases

    You mean onyx vs monkeybeavers? That's what I'm wondering I figure this is an onyx thread

New threads New posts

Kask Stihl NORTHEASTERN Arborists Wesspur TreeStuff.com Teufelberger Westminster X-Rigging Teufelberger
Back
Top Bottom