Rubber hits the slick metal

To consider. A friend of mine pestered me to weld repair his detached, broken, edge of it's expanded metal floor of the tailgate of his trailer. Cost/price/friendship I just said no thanks. But I explained in detail the equipment, supplies and techniques involved so he could charge off and fix it himself (like new, and guaranteed not to re-break;)) in an afternoon with no $ outlay ;)

Point being expanded metal may tear out supporting load. And pita to repair such.

Grip tape or paint on grit may not be effective for moderate mud. rain, ok. I vote expanded fastened to floor. skaters call it grip tape since the 70's
 
  • Like
Reactions: ATH
Thinking through the expanded metal again:
Maybe I bolt it down instead of weld. Put either a rubber mat or rubberized paint (rhino lining like). Then a couple of times a year take it up see how it looks...if necessary, sand/prime/paint / fluid film? / bolt it back down.

Edit: or maybe put the rubber coating down first and then do a rubber coating on top of it to try to seal the gaps underneath as Evo suggested above
 
Last edited:
Thinking through the expanded metal again:
Maybe I bolt it down instead of weld. Put either a rubber mat or rubberized paint (rhino lining like). Then a couple of times a year take it up see how it looks...if necessary, sand/prime/paint / fluid film? / bolt it back down.
If you put down a good bedliner material, like LineX, you should not need to take the expanded metal up at all. Is buying an aluminum bad a possibility? I know it may be a little expensive to come pick up the truck, but there's a shop here local that would build you anything you like,
 
  • Like
Reactions: ATH
If you put down a good bedliner material, like LineX, you should not need to take the expanded metal up at all. Is buying an aluminum bad a possibility? I know it may be a little expensive to come pick up the truck, but there's a shop here local that would build you anything you like,
If I get a cab and chassis, all of this may be a moot discussion as I would just get a bed with some traction. But it is looking like that's going to be at least $10,000 (maybe $15k) more than the one truck I found that is already built as I want it... I found a place here that will build custom as well so that is on the radar.
 
You can improve you ramp angle with wooden blocks or 1 beam under the low end. You will be able to crawl up on the ramp where some vehicles wouldn't be capable of getting over the lip.
 
  • Like
Reactions: ATH
If I get a cab and chassis, all of this may be a moot discussion as I would just get a bed with some traction. But it is looking like that's going to be at least $10,000 (maybe $15k) more than the one truck I found that is already built as I want it... I found a place here that will build custom as well so that is on the radar.
That seems like a very big difference, and I don't understand why it would be such a difference. Having a bed that's built exactly as I want it would be worth that much to me, but that's just me.

Give a call to Gap Hill Aluminum Shop, here in Gap, PA and see what he would charge for the bed you want. You might be surprised at what you hear. He can build and install us a new custom 18' aluminum chip body with PTO hoist, toolboxes under the whole bed, and all our preferred lights for under $30k. Seems a flatbed should be less than $10k installed.
 
  • Like
Reactions: ATH
That seems like a very big difference, and I don't understand why it would be such a difference. Having a bed that's built exactly as I want it would be worth that much to me, but that's just me.

Give a call to Gap Hill Aluminum Shop, here in Gap, PA and see what he would charge for the bed you want. You might be surprised at what you hear. He can build and install us a new custom 18' aluminum chip body with PTO hoist, toolboxes under the whole bed, and all our preferred lights for under $30k. Seems a flatbed should be less than $10k installed.
Thanks...I'll call if we get there.

The cheapest I've found is just under $10K for steel with a wood deck. That's a Knaphied. There is a fabrication shop i need to talk to - they always have beds sitting out that I assume they are making. One of their brothers owns a tree company so maybe they won't want to help LOL!

The cost difference is partly because the one is a leftover 2026. Others are 2027. The 2027 is also a heavier capacity - but I don't need that. We'll see where actual quotes vs estimates come.
 
Also....the lighter truck means I don't need to reclassify a trailer to stay under CDL.

The bed is what I want except for the surface. That's worth a little, but not several thousand to me
 

New threads New posts

Back
Top Bottom