Rubber hits the slick metal

ATH

Been here much more than a while
Location
Findlay, Ohio
Thinking of getting a flatbed truck to transport the Avant (528, if that matters). Many of the flatbeds available are smooth metal. Concerned that when its wet or muddy, that the machine won't be able to make the final climb off of ramps onto the bed.

A) How much of a realistic concern is this? (currently putting it in a dump trail with a smooth bottom...but it has a little better approach angle sitting lower than a truck bed will...but will get longer ramps for truck).
B) What can I do about it? Thought of expanded metal, but sounds like that is a great recipe for rust. Maybe bolted down rubber mats???

ideas?
 
I bought a trailer recently from a guy that used it to haul his side by side thing, it had some metal tracks bolted to the bed that I assumed were for tire grip.
What did the tracks look like? I've seen a suggestion of just putting a few pieces of small rebar at the back - just to make it over the hump as it were
 
I can see that being a challenge when the tires are wet or muddy. A diamond plate deck would probably be better to load on, a wood deck is also better. Another option would be a bit of expanded metal or even just some lines of hard surface welding rod might be enough.

Is this flatbed going to dump, or are you just going to use it to haul equipment and materials?
 
I can see that being a challenge when the tires are wet or muddy. A diamond plate deck would probably be better to load on, a wood deck is also better. Another option would be a bit of expanded metal or even just some lines of hard surface welding rod might be enough.

Is this flatbed going to dump, or are you just going to use it to haul equipment and materials?
That last part is a really important point to consider
 
You can go cheapest route first and buy that grippy adhesive strip they put on stair treads for the first foot or two. Non-slip stuff, like an asphalt shingle but a little less grainy
 
I had a trailer with ramps that lined up just so that my stumper couldn’t climb if wet or muddy. So I welded 3/8” nuts every 4” up the ramps, problem solved. And the 3/8” nut is just what I had on hand no rhyme or reason to them. I think anything would work and I haven’t noticed any obvious wear to the rubber.
 
I can see that being a challenge when the tires are wet or muddy. A diamond plate deck would probably be better to load on, a wood deck is also better. Another option would be a bit of expanded metal or even just some lines of hard surface welding rod might be enough.

Is this flatbed going to dump, or are you just going to use it to haul equipment and materials?
Just looking for a flat bed. Dump would be nice every now and then. Now we put the loader in dump trailer. But we have to go back to get it when we also need the trailer that means 2 trips. Also when planting trees could put trees on flatbed and loader in trailer.

I guess I could weld some diamond plate onto a smooth bed. Probably 18-24" across the back would do it.
 
Try heavy expanded metal. Either cut in strips or just a sheet.
That was my first thought...but apparently as dirt gets under that it really accelerats rust. I can only imagine getting salt spray in there too.

Any ideas to use expanded metal in a way that could alleviate that concern?
 
That was my first thought...but apparently as dirt gets under that it really accelerats rust. I can only imagine getting salt spray in there too.

Any ideas to use expanded metal in a way that could alleviate that concern?
Stainless? Galvi? Can’t speak to salt, but just be diligent with a leaf blower and or garden hose? Could even cut the ‘skin’ off the steel flatbed the same width of the tires (and wheel base) and weld in the expanded so it passes through to the road.. aka no interface lasagna
 
Last edited:
  • Like
Reactions: ATH
Making an cutout is a great idea. Though the thought of putting the plasma touch to a brand new truck is a bit hard to think.

(Not finding what I want used - crew cab cab over truck (to limit length and shorten turning radius))
 
Making an cutout is a great idea. Though the thought of putting the plasma touch to a brand new truck is a bit hard to think.

(Not finding what I want used - crew cab cab over truck (to limit length and shorten turning radius))
I run into that frequently, want vs available to fulfill the need.
I’d imagine that hypothetical if the tires are 16” wide you’d get away with 8-10” expanded width if doing strips.
You can also consider welding them straight into the deck, and using a heavy coat of rhino bedliner. I have seen this where it fills the gaps where water/debris can collect but providing a traction surface.
While we don’t deal with road salt in any appreciable amount, we get slick wood beds all the time from the pnwet slime that grows on everything.
 
  • Like
Reactions: ATH
Paint, fluid film, and keep it cleaned out.
Reality...not gonna power wash on a regular basis on winter. Unheated shop, so even if we did, that's make it more slippery.

But I've never used Fluid Film, so would we put that on liberally early winter and the wash out when conditions are appropriate? Reapply after washing?

I do like the idea of "sealing" with rhino liner type paint.
 
Just looking for a flat bed. Dump would be nice every now and then. Now we put the loader in dump trailer. But we have to go back to get it when we also need the trailer that means 2 trips. Also when planting trees could put trees on flatbed and loader in trailer.

I guess I could weld some diamond plate onto a smooth bed. Probably 18-24" across the back would do it.
Buying a bed with a diamond plate top would be a good idea, there's also a really gritty paint-on coating made for tire traction on truck beds. I have referenced the name of it on this forum before, but it's been a while and I don't recall the name. If you are better at using the search function than I am, you can probably find it on here somewhere.
 
  • Like
Reactions: ATH
Buying a bed with a diamond plate top would be a good idea, there's also a really gritty paint-on coating made for tire traction on truck beds. I have referenced the name of it on this forum before, but it's been a while and I don't recall the name. If you are better at using the search function than I am, you can probably find it on here somewhere.
I'm currently looking at 2 options:
A) Complete truck with bed on it. It's slightly lighter duty than option B, but fits our needs...and is probably going to be $15,000-20,000 less. Need to figure out delivery so that'll obviously impact price. It has a smooth metal bed.
B) Buy a cab and chassis truck and pick the bed I want...seems like wood is the most practical option. I'd probably screw a piece of expanded metal to that. Still working on some final pricing numbers here.


I'm looking for options if I go (A). So far, I think the 2 I like best are cutting openings for expanded metal or weld diamond plate across back. But maybe I should try grit paint first as that's "less intrusive".
 
Buying a bed with a diamond plate top would be a good idea, there's also a really gritty paint-on coating made for tire traction on truck beds. I have referenced the name of it on this forum before, but it's been a while and I don't recall the name. If you are better at using the search function than I am, you can probably find it on here somewhere.
It was March. Apparently I've been stewing over a truck since then LOL.

You dug it up.for me then! Thanks for the reminder: in the equipment hauler thread

Scorpion Bedliners
 

New threads New posts

Back
Top Bottom