Treezybreez
Been here much more than a while
- Location
- Lancaster, SC
I can't remember if Gordon tried the support hooks for the top or not. Even if it did improve the device, I doubt there will ever be a "final step" LOL!
Akimbo vs BDB
- Thread starter Jpennay
- Start date
Steve Connally
Been here much more than a while
- Location
- Suffolk, Virginia
Sweet!!!
I did make a Bone called the Stubby with the same top arms as the bottom arms, back in 2017. It never seemed to catch on, and I have been too busy to play with that design anymore anyway. Perhaps I will have to revisit that design with the new spine and the elongated bollard. : )
That would be tremendous, Gordon. I believe the lack of interest in the Stubby was related to it being 1/2" rope specific. I had planned on to getting one because I do use 1/2" rope, Vortex, but life got in the way.
Having the additional safety that the top hooks would impart on the current BDB model would be a great addition.
Having the additional safety that the top hooks would impart on the current BDB model would be a great addition.
- Location
- Philadelphia
You can detach the akimbo while still clipped in with a biner?!
Merle Nelson
Been here much more than a while
- Location
- SF Bay Area, CA
Lanyard in, remove Akimbo for whatever reason, re-apply Akimbo, detach lanyard and your off.
Yes you can.
CutHighnLetFly
Been here a while
- Location
- Cape Cod, MA
The major problem I have with Akimbo vs the Bone is the Akimbo's bottom attachment. It's a pinch point / friction plate. So when you sit into it, it's pressing on the line, and when unloaded it can move a bit.
My problem was when you release the device to descend, in an effort to make a smooth long descent on a swing or to just a lower point in the tree the device goes, very quickly, from quick descent to almost freefall like fast drop. (@JMerritt I saw an Akimbo prototype my buddy has with a new attachment point that looks like it resolves this issue. Thing was really cool)
The bone can't really ever go into free drop mode. All this leads to the Akimbo being smoother going up, but I don't like the trade.
My problem was when you release the device to descend, in an effort to make a smooth long descent on a swing or to just a lower point in the tree the device goes, very quickly, from quick descent to almost freefall like fast drop. (@JMerritt I saw an Akimbo prototype my buddy has with a new attachment point that looks like it resolves this issue. Thing was really cool)
The bone can't really ever go into free drop mode. All this leads to the Akimbo being smoother going up, but I don't like the trade.
Last edited:
dsptech
Branched out member
- Location
- North East
Do tell us more about this prototype that you have seen.
JMerritt
Branched out member
- Location
- santa cruz
which one was this? if its jerky on descent try tightening up the bottom setting. i am working on a different spring placement. it seems that is one of the major reasons the akimbo sucks at sap so much.
CutHighnLetFly
Been here a while
- Location
- Cape Cod, MA
@JMerritt I saw an Akimbo prototype with a different attachment point / bottom friction po
Ugh I dont know too well how to explain it. It's. It that it was jerky as much as trying to dial in that fast descent control was getting me. But this one I saw (my buddy Josh Burr had it), that attachment point / friction point moved a lot less and when unloaded. Definitely seemed like if you were to break the device wide open, it would be more controlled. Either way man, really neat to have been seeing you here developing it
Z'sTrees
Branched out member
- Location
- Hartsel CO
How does the bollard adjust on the new style Bone?
Fwiw, I've used both extensively and they're both great tools. Very similar too. I'd say the akimbo is a bit more refined and adjustable, which can be a drawback too.
The Bone is rock solid, rebuildable, and a bit more intuitive to set up and use.
Fwiw, I've used both extensively and they're both great tools. Very similar too. I'd say the akimbo is a bit more refined and adjustable, which can be a drawback too.
The Bone is rock solid, rebuildable, and a bit more intuitive to set up and use.
The adjustable bollard in the top arm of the Bone adjusts by means of a stainless steel 10-32 machine screw which pushes or pulls the slotted and threaded bollard. It does require a Phillips screw driver, however you do not need to take the rope out of the Bone to make this adjustment.
