Recent content by Dead Cottonwood

  1. Dead Cottonwood

    What’s Your SMALLER Equipment Setup?

    I’ve got a 935 w/ Perkins as well and it is amazing. Keep the knives sharp and it’s a beast. No clutch (engine slides into drive belt), pre emission, light and maneuverable. Wish they still made them
  2. Dead Cottonwood

    How's the work flow?

    Booked out three weeks right now but historically have been out two months this time of year.
  3. Dead Cottonwood

    Stihl 201T high idle even w/idol screw fully backed out

    dug a little deeper in the saw and found no signs of cracked hoses, seals, and gaskets. Looking like I’m just going to buy a new saw while I break this one down further. Thank you all for your input and assistance.
  4. Dead Cottonwood

    Stihl 201T high idle even w/idol screw fully backed out

    Thank you. I will look into this tomorrow
  5. Dead Cottonwood

    Stihl 201T high idle even w/idol screw fully backed out

    Had a 201T for over 10 years w/no issues. Recently it kept dying while idling even after carb adjustment. Cleaned the carb but still doing the same thing. This saw has been ran hard for over a decade and owes me nothing but would like other’s opinion on if it’s fixable or if it needs to be...
  6. Dead Cottonwood

    Someone please design an industrial level version of the fiskar telescoping pole pruner

    Yeah those look nice. I emailed the link to sappy supplies and monkey beaver. Hopefully we can get those sold by good people here in the U.S.
  7. Dead Cottonwood

    Someone please design an industrial level version of the fiskar telescoping pole pruner

    Yes that is a great feature. If removing a branch over something fragile, we’ll hold the branch with the fiskars and cut it with the pole saw.
  8. Dead Cottonwood

    Someone please design an industrial level version of the fiskar telescoping pole pruner

    Not enough reach to justify in my opinion
  9. Dead Cottonwood

    Someone please design an industrial level version of the fiskar telescoping pole pruner

    Yep. Accurate, rapid fire, pump action pruning cuts
  10. Dead Cottonwood

    Someone please design an industrial level version of the fiskar telescoping pole pruner

    Someone with skills and time should create an industrial version of the fiskar telescoping pole pruner. It’s such a useful tool but aren’t built heavy duty enough for extended use in tree commercial tree work. You could market it on sappy supplies or monkey beaver and become a billionaire and I...
  11. Dead Cottonwood

    Anybody tried the 25 cfm airspade nozzle w/smaller compressor?

    I have, just wanted the knowledgeable opinions of my fellow tree people of treebuzz
  12. Dead Cottonwood

    Anybody tried the 25 cfm airspade nozzle w/smaller compressor?

    Thank you for the input. My estimations put a smaller compressor (approx 12hp) mounted on a DR Power Wagon with the 25cfm airspade costing about half the cost of just the tow behind compressor. I’ve never seen the 25cfm airspade in use so my main concern is I invest in this smaller stuff and it...
  13. Dead Cottonwood

    Anybody tried the 25 cfm airspade nozzle w/smaller compressor?

    This is the one I was referring to. Specs say minimum compressor horsepower 5.6 https://www.airspade.com/products/airspade-2000?variant=9498230521900
  14. Dead Cottonwood

    Anybody used the 25 cfm airspade nozzle w/smaller compressor?

    If so, how effective was it and is it worth purchasing. Looking to build a small, portable air spade setup and wondering if that 25 cfm will get the job done
  15. Dead Cottonwood

    Anybody tried the 25 cfm airspade nozzle w/smaller compressor?

    If so, how effective was it and is it worth purchasing. Looking to build a small, portable air spade setup and wondering if that 25 cfm will get the job done
See more

New threads New posts

Back
Top Bottom