802climber
Participating member
- Location
- Southern Vermont
2002 INTL 4400 DT466E (Pre-emissions)
33K GVWR - CDL Required
Aerial Lift of CT 60-50 (60’ Max Working Height 50’ Max Side Reach)
17247 hrs 185416 mi
Fits ~60 4x8 mats on bed or a small mini skid if you wanted to go that route
~3000 hrs on inframe engine rebuild / upgraded injectors turbo & radiator (per intl), is now ~275HP.
This was a remount built at ALC factory in 2008 and is the tightest ALC I’ve ever ran. Both cylinders have been rebuilt w/ the good rods. Bullgear & hoses also replaced.
Fresh ANSI on the lift (pass).
Fresh dielectric test on the lift - Upper boom and liner passed, lower boom failed due to moisture inside the isolator. Have not yet had it retested on a drier day. Has always passed for the last 8 yrs.
Good tires
Always oil undercoated
Air shift PTO
1 Tool Circuit @ platform
Quick connect for blowing out saws, filling up tires etc.
Includes:
Full fuel tanks
Fresh oil and filters before sale
All manuals (ALC & INTL)
Alturnamat Outrigger Pads (4)
Wheel chocks (2)
Fire extinguisher (1) and safety triangles (3)
Spare brand new bucket liner
ALC rope brake (receiver hitch mounted, multiple mounts throughout truck body)
Underbody hooks for tire chains
Heat/AC/radio (AC needs fixed)
Will need a clutch & brakes before too long
Windshield cracked
Needs to be washed!
Selling due to lack of CDL drivers. Picked up 2 under cdl trucks in the last 6 months.
Located in Southern Vermont.
$35K cash/certified check.
Clear VT title.
Can easily get temp plates out of VT.
May trade for a clean 12” bandit disc chipper with winch such as a 200xp or 250xp less than 15 years old or so. Dont need anything larger than that at this time.
33K GVWR - CDL Required
Aerial Lift of CT 60-50 (60’ Max Working Height 50’ Max Side Reach)
17247 hrs 185416 mi
Fits ~60 4x8 mats on bed or a small mini skid if you wanted to go that route
~3000 hrs on inframe engine rebuild / upgraded injectors turbo & radiator (per intl), is now ~275HP.
This was a remount built at ALC factory in 2008 and is the tightest ALC I’ve ever ran. Both cylinders have been rebuilt w/ the good rods. Bullgear & hoses also replaced.
Fresh ANSI on the lift (pass).
Fresh dielectric test on the lift - Upper boom and liner passed, lower boom failed due to moisture inside the isolator. Have not yet had it retested on a drier day. Has always passed for the last 8 yrs.
Good tires
Always oil undercoated
Air shift PTO
1 Tool Circuit @ platform
Quick connect for blowing out saws, filling up tires etc.
Includes:
Full fuel tanks
Fresh oil and filters before sale
All manuals (ALC & INTL)
Alturnamat Outrigger Pads (4)
Wheel chocks (2)
Fire extinguisher (1) and safety triangles (3)
Spare brand new bucket liner
ALC rope brake (receiver hitch mounted, multiple mounts throughout truck body)
Underbody hooks for tire chains
Heat/AC/radio (AC needs fixed)
Will need a clutch & brakes before too long
Windshield cracked
Needs to be washed!
Selling due to lack of CDL drivers. Picked up 2 under cdl trucks in the last 6 months.
Located in Southern Vermont.
$35K cash/certified check.
Clear VT title.
Can easily get temp plates out of VT.
May trade for a clean 12” bandit disc chipper with winch such as a 200xp or 250xp less than 15 years old or so. Dont need anything larger than that at this time.
Last edited:
