Bandit 1890HD and GMC Topkick Combo

Discussion in 'TreeBay' started by Keeth, Jun 15, 2017.

  1. Keeth

    Keeth Active Member

    Joined:
    Nov 24, 2014
    Messages:
    106
    Location:
    NC
    2004 1890HD: 1600 hours, genuine CAT 3056 engine, single axle dually wheel configuration, 3 sets of knives, has a winch with synthetic line. Always serviced before manufacturer's recommended intervals. As seen in video below, Auto-feed control reads 650hrs (replaced at 950hrs, still have old one). Runs and chips beautifully!

    1989 Topkick with 95k miles. CAT 3208T engine, Allison automatic, fresh brakes (they are hydraulic) and lines, good tires, 12 foot dump, 28k GVWR. Power steering box leaks. Other than that, it starts on the coldest mornings and pulls strong.

    Video walk-around:



    Location is Boone, NC (28607). Price is $40,000 for the pair.
     

    Attached Files:

    Last edited: Jun 16, 2017
  2. Z'sTrees

    Z'sTrees Well-Known Member

    Joined:
    Aug 11, 2014
    Messages:
    323
    Location:
    NW NC
    I've seen that chipper parked, I was wondering who owned it. Good luck with the sale, nice machine.
     
    Keeth likes this.
  3. cory

    cory Well-Known Member

    Joined:
    Oct 2, 2004
    Messages:
    1,795
    Chipper looks fine from that angle. Why are the hours so low on the 13 Y O machine?
     
  4. Keeth

    Keeth Active Member

    Joined:
    Nov 24, 2014
    Messages:
    106
    Location:
    NC
    I ran the business on the side when I was still teaching. The chipping one of these does in one hour is equivalent to three or four hours on a 12 inch machine.
     
  5. cory

    cory Well-Known Member

    Joined:
    Oct 2, 2004
    Messages:
    1,795
    Makes sense. Similar to large stump grinders having low hours despite their age, very few stumps take much time.
     
  6. LiTreeService

    LiTreeService Member

    Joined:
    Jan 31, 2015
    Messages:
    61
    Location:
    Long Island
    Standard feed wheels or oversized?
     
  7. Keeth

    Keeth Active Member

    Joined:
    Nov 24, 2014
    Messages:
    106
    Location:
    NC
    Oversized infeed and wheels. You should be able to see them about half way through the video.
     
  8. cory

    cory Well-Known Member

    Joined:
    Oct 2, 2004
    Messages:
    1,795
    That chipper looks mint. Is that an 18" chipper or maybe 19"? Btw, please don't open the hood with drum spinning, it's just wrong.
     
    LiTreeService and Keeth like this.
  9. Luzl78

    Luzl78 Member

    Joined:
    Oct 1, 2014
    Messages:
    33
     
  10. Luzl78

    Luzl78 Member

    Joined:
    Oct 1, 2014
    Messages:
    33
    Keith, how much for just the chipper? Thanks. Jeff in nj
     
  11. Keeth

    Keeth Active Member

    Joined:
    Nov 24, 2014
    Messages:
    106
    Location:
    NC
    $35,000
     
  12. TreelineNH

    TreelineNH Active Member

    Joined:
    Jan 15, 2015
    Messages:
    151
    Location:
    Southern, New Hampshire
    Does it have reversing autofeed?
     
  13. Keeth

    Keeth Active Member

    Joined:
    Nov 24, 2014
    Messages:
    106
    Location:
    NC
    Yes, fully programmable. Raise or lower both cut-in and back-off RPMs. I believe there's a timing feature as well. However, I've never needed to adjust anything.
     
  14. John Arborman

    John Arborman New Member

    Joined:
    Dec 28, 2016
    Messages:
    1
    Location:
    Springfield
    Hi Keeth. I'm interested in your 1890. Would you give me a call at 217-789-6000 to discuss. Thanks.

    John
    217-789-6000
     

Share This Page