Adventures with treemek

Discussion in 'Crane Use' started by Carolinatreeco, Oct 15, 2017.

  1. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
  2. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville

    Here's another one
     
    treebilly and NE Tree like this.
  3. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
  4. treebilly

    treebilly Well-Known Member

    Joined:
    Feb 10, 2015
    Messages:
    389
    Location:
    N. Lawrence
    These things need a set of power rollers like the timber processors. Cut, hold, feed it directly into the feed rollers of the chipper, and release

    Bad ass videos by the way.
     
    Carolinatreeco and Jehinten like this.
  5. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
    Yes and it would be cool if you could cut logs that way. Cut it 12' long roll up and take it away.

    Thanks
     
  6. treebilly

    treebilly Well-Known Member

    Joined:
    Feb 10, 2015
    Messages:
    389
    Location:
    N. Lawrence
    I was just thinking enough to put it in the feed rollers. I'm kinda spoiled on the chipper end. A bc 2100 don't care to much about crotches or firewood or millable logs.
     
    LiTreeService and Carolinatreeco like this.
  7. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
  8. deevo

    deevo Well-Known Member

    Joined:
    Aug 5, 2010
    Messages:
    1,685
    Location:
    Horseshoe Valley, Ontario, Canada
    Ha ha that’s awesome and even more impressive with my favourite bands music! Great job, you going to the tree expo this week? Your cranes awesome and the perfect setup! @SJ_Treeguy
     
    JD3000 likes this.
  9. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
    Yes I will.
     
    deevo likes this.
  10. deevo

    deevo Well-Known Member

    Joined:
    Aug 5, 2010
    Messages:
    1,685
    Location:
    Horseshoe Valley, Ontario, Canada
    Great I’m sure I’ll run into ya ! Get the low down on your truck
     
  11. JD3000

    JD3000 Well-Known Member

    Joined:
    Aug 28, 2016
    Messages:
    4,086
    Location:
    Columbus
    Pass the Mic. Outstanding choice.
     
    Carolinatreeco likes this.
  12. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville
    I’ve never been to one. Very excited to go. Definitely I’ll talk about it for sure.
     
  13. Carolinatreeco

    Carolinatreeco Member

    Joined:
    Feb 13, 2017
    Messages:
    32
    Location:
    Greenville

Share This Page